| View previous topic :: View next topic |
| Author |
Message |
JasonG1974
audio school
Joined: 19 Apr 2011
Posts: 4
|
 Posted: Tue May 24, 2011 2:30 pm Post subject: TEAC 80-8 DIY control cable for DX-8D DBX unit need pinouts |
  |
|
I have a TEAC 80-8 that doesn't have the 11 pin DBX control cable and a DX-8D DBX unit. I have the parts to make the cable but am having a hard time figuring out the pin configuration (which number pin on the male plug goes to which upper or lower contact on the 80-8 pc board) and I'm hoping someone who's been to this rodeo before or who has an 80-8 with the original DBX control cable could assist me. Thanks.
_________________
Jason G |
|
| Back to top |
|
 |
boot_me
audio school
Joined: 20 Apr 2010
Posts: 4
Location: Sheridan,Or
|
| Posted: Sun Dec 18, 2011 4:33 pm Post subject: did you ever get this done? |
|
|
I have an 80-8 with a dbx unit... the cable between the two is is intact. If I can figure out what you need I would be happy to try and figure it out.
_________________
bootme |
|
| Back to top |
|
|
JasonG1974
audio school
Joined: 19 Apr 2011
Posts: 4
|
| Posted: Sun Dec 18, 2011 5:11 pm Post subject: Re: did you ever get this done? |
|
|
| boot_me wrote: | | I have an 80-8 with a dbx unit... the cable between the two is is intact. If I can figure out what you need I would be happy to try and figure it out. |
Thanks so much. I forgot to follow up on this thread. I had also posted on a couple others.
I finally found a gentlemen who was kind enough to go to the trouble of giving me the proper pinouts and was able to make a really good cable which functions perfectly. Then I had the good fortune of finding an original cable on Ebay for like $30 so I went ahead and grabbed it. You NEVER see these listed! I couldn't believe it! I made a nice pinout diagram for future reference also so anybody who needs it can send me a PM or you might find where I have posted it on other forums. Thanks again and happy holidays!
_________________
Jason G |
|
| Back to top |
|
|
boot_me
audio school
Joined: 20 Apr 2010
Posts: 4
Location: Sheridan,Or
|
| Posted: Sun Dec 18, 2011 5:52 pm Post subject: thanks |
|
|
Thanks, glad you got it all sorted out.
Happy Holidays
_________________
bootme |
|
| Back to top |
|
|
Blue Jinn
audio school
Joined: 02 Mar 2010
Posts: 7
Location: see homerecording.com bbs
|
| Posted: Wed Dec 28, 2011 4:17 pm Post subject: Re: did you ever get this done? |
|
|
| JasonG1974 wrote: | | boot_me wrote: | | I have an 80-8 with a dbx unit... the cable between the two is is intact. If I can figure out what you need I would be happy to try and figure it out. |
Thanks so much. I forgot to follow up on this thread. I had also posted on a couple others.
I finally found a gentlemen who was kind enough to go to the trouble of giving me the proper pinouts and was able to make a really good cable which functions perfectly. Then I had the good fortune of finding an original cable on Ebay for like $30 so I went ahead and grabbed it. You NEVER see these listed! I couldn't believe it! I made a nice pinout diagram for future reference also so anybody who needs it can send me a PM or you might find where I have posted it on other forums. Thanks again and happy holidays! |
Do you mind posting this, or a link? This would be helpful info to have.
Thanks, Pm'd ya too. |
|
| Back to top |
|
|
|
