Message Board

If it's a NAB hub, that is the only screw. some times, they stick on after time; you'll will have to rock it back and forth or use some thing (screwdriver, butter knife) to help it off.

if you are using 48 tracks that's two 2 inch tapes at once ($$$) and a reel of 2,500ft at 15ips is 30minute at 30ips 15minute

you can go to tapetape.com for one pass tape (cheap 65ish) or buy new tape ($$$)

if you go to chain stores expect to pay over 150 for 2 inch tape

i have a RE20; it is by far one of the best dynamic mics i have

i whish i could use a m88 for a day and a/b it but, i don't know any one that has one

i got my RE20 for $150 (CHEAP)

if you get a good price on either buy it

this is just my opinion

for a cheep price but good kick sound i've used the mk 219 and/or mc 012 (oktava) out side of the drum with pads on and i felt it beat the D4, D112, and B52 for the 219 about 2-3 inch dead center but, you may need to move it back to suit the drum for the mc 012 either 6-12 inch dead center as the mi...

i have a d4. it sucks unless you like death metal kick drum sounds it has to much attack and mid range with no real bass; you will need to EQ a lot mainly in the 400-600 range and it still is tacky cardboard sounding if you go to Audix's web site and look up the D4 you will see it's frequncy respons...

press club dosen't have a stage any more

powerhouse sucks (again, stay out of the burbs stay downtown)

torch club is a blues spot



recording engineer, is your spot on Main or Greenback

hey deafinONEear, Sacto Spots that haven't been listed yet Cafe Metro on Kst (they have small all ages shows in the summer w/ beer) Distillery on 21st and Lst (smaller than Old Ironsides 21+) Fox and Goose on 10st (brit pub w/ stage 21+) Harlows on Jst (2 floors w/bars very trendy most of the time b...

yes, the g16 is good buy the fact that it's 16 tracks but i'd rather have a 1" 8 track but, i can't afford one of those.

is the b16 a 2 or 3 head deck

the g16 is a 2 head

now if i can get a 15ips IEC MRL tape i'll be stoked

i was using the d-mag and it dosen't seem to have that strong of field
compaired to the ones i use at school (you could pick up keys and whipe out credit-ID card strips etc)

this one only picks up paper clips

is this bad for the tape deck?

I haven't used it on the tape deck yet; should I use it?

this one is a 2 prong also with a short cord (i'll just use an extension)

i'll try it on my teac 3340 first then my fostex g16

I bought a d-mag at a thrift store today. It's an Audiotex (cat. no. 30-112)

it is smaller than ones i have used before whith a button you hold down at the top

it has a UL listing but i am still afraid to use it

what do you think?

I know the 3m is used (1 pass tape from tapetape.com) I dont mind it for tracking though, I buy new for mix down. when I go to Quantegy's web sight they only list the coercivity (oersteds) I would like to use +9 but +6 is good is the 966 a +6 or a +9 What about 900 and 911 I have a 2 head fostex g16...

what about 3M and BASF/Emtec

I have used 996 on other tape decks and i liked it (i know it's a +9) but, what about 966

if my tape deck's recording level is 320nwb/m what tape do i use for Ampex/Quantegy, 3M, and BASF/Emtec.

I've checked and Mark's web sight and it dosen't have it

I know I sound like a cheep basterd but I'm trying to save money for a good MRL tape

thanks

if any one has any insight on this tape deck I'm all ears