Message Board

Sorry, I just shipped it out last night. Didn't have a chance to modify the ad after the fact.

Thanks,

Jay

VS-100 is most likely sold.
AT Mic is gone.
Possible sale on the 3630
SM Pro a08 is pending sale

all else still up for grabs

-Jay

Most of this probably won't interest you guys but It's gotta go...... Big upgrades lately, hoping to clear out the closets. Vintage Univox 12" Speaker 30watts $15 Behringer UB802 mixer w/box & power supply $30 Samson S Amp 2 channel w/Power supply $25 Samson CO1 Condensor Microphone w/Hardcase $40 (...

Brian, I'll have to hit those with the multi-meter. I hadn't thought about the possibility of them being mil-spec resistors. The plastic can in the pic is a capacitor associated with the phantom end of things. I seem to have cropped the input transformer off. The beyer xfmr is a silver bulb-ish thin...

I uploaded a pic of the top of the board and a half assed scan of the traces below. They are at the original link that I posted.

Thanks,

Jay

Brian, The black things have the following ledgible markings: MM60 750IF NA60 I have no Idea what they are, but storngly guess diodes. The Beyerdynamic # is TR/BV351 015 006 then (I assume a date code of) 01 76 The resistors around the non-inverting inputs are: Pin 6 - 100k Pin 8 - 33K Will a DI inp...

Brian, If I run at 24VDC to the supply, and the zero point of pin 2 is +12V isn't that too high to feed into say my MOTU 2408's? seems like alot of juice to me.......... The phantom supply is less of a concern to me, I could always use a Rolls box out front if I need it. I want these to run kick and...

Brian, thanks for the reply. the transformer has a third leg on that side which I should assume is a tap (?), coul I be mistaken in my drawing? could that be a second winding sharing the ground for some reason? So what would you guess for supply? the specs on the chip say 15-18 volts, but there is r...

They look correct to me, at least as correct as they were when scanned :) . At the right it looks like it cut off (where it says "pin 23") but that IS the edge of the page. it's all there, except the EQ section which is on a different page. If you'd like, I can email them directly just in case. Than...

I will be starting a new record with my band and I'm planning on using a bunch of huge locations locally to capture the drum tracks. I plan to implement this with 4 Oktava MK-219s. They lend well to overhead and room imaging so I believe they are good candidates. I'll keep you all posted. Should be ...

Let me add a question to this question for a second: What if you, before what ever the amp is, just combine the L+ and R+ (line level) and drive the amp from that? is this bad for the input stages on the amp? or possibly the output stages of the console/interface/machine? why do you need to sum them...

Brian,

Have you had a chance to review the schematics? I am going to build a box for them this weekend and *try* and get one functioning. I'll post results.

Thanks,

Jay

Pm sent for Oktava 319.

ttt

I put the Lil' Puncher bridge p/u in a Tele-copy that I keep in the studio. I have push pulls on both knobs and no tone control. 2 volume knobs. Front pickup is stock and its p/p does phase. Rear is the GFS Lil' Puncher and its p/p taps the 'bucker to a single coil. alot of cool combinations to be h...

Hey guys,

I went ahead and uploaded them to a directory on my site.

The schematic is messy and I make no excuses for that, but it should be helpful in this whole deal.

so.........

http://www.fartoofrail-music.com/stevenson/

I will take some pics when I find my camera cable.

Thanks,

Jay