Soundcraft Ghost interfacing with recorders
-
- suffering 'studio suck'
- Posts: 434
- Joined: Wed Apr 15, 2009 9:43 am
- Location: saint paul, mn
Soundcraft Ghost interfacing with recorders
Recently bought a Soundcraft Ghost, and today as I started the task of getting it setup, I realized that the direct outputs on the channels have a nominal level of -2dBu (unbalanced). Seems ridiculous, I guess I should have done my homework more thoroughly before buying this thing.
I know this is a popular board so I'm curious what others have done as far as interfacing this thing with recorders that are designed for either +4 or -10. I use both a Lynx Aurora and a Tascam MS16 tape machine. Both can be set for either +4 or -10, but this -2dBu thing has me baffled. If I was only recording digitally I could see it not being a real issue, but getting proper level onto tape is a bit more critical.
I'd like to just run everything at +4 so that I'm not dealing with level mismatches while using some console pres and some outboard pres during the same session. But apparently that's not in the cards for me. If anyone has some advice about optimal setup for this board, I'd appreciate it. Thanks!
I know this is a popular board so I'm curious what others have done as far as interfacing this thing with recorders that are designed for either +4 or -10. I use both a Lynx Aurora and a Tascam MS16 tape machine. Both can be set for either +4 or -10, but this -2dBu thing has me baffled. If I was only recording digitally I could see it not being a real issue, but getting proper level onto tape is a bit more critical.
I'd like to just run everything at +4 so that I'm not dealing with level mismatches while using some console pres and some outboard pres during the same session. But apparently that's not in the cards for me. If anyone has some advice about optimal setup for this board, I'd appreciate it. Thanks!
- Wagz
- takin' a dinner break
- Posts: 186
- Joined: Mon Sep 08, 2008 4:44 am
- Location: Kalispell, MT
- Contact:
Hi Matt,
I am in the same boar actually. I just installed a Ghost at my studio on Sunday this week and am still unsure on what levels to run at. So anyone with advice feel free to chime in. Still working on what I want to do for workflow.
So far, when I was calibrating my oputputs from pro tools into the board via the tape returns I was setting it with the outputs set on my aurora to -10 normal. Then when I was running a two buss into a compressor I noticed I was cranking the input on that thing up quite a bit more than when I was on my previous setup.
So after setting my returns I switched the outputs back to +4 and it seems to work a little better. well, I get more in two buss going out, and the headroom seems to be able to handle it without collapsing. At least with my minimum experience so far.
With the inputs on PT I have them set to -10.
For my line in's I just set my trim levels for my outboard gear and leave 'em.
One option too. And I'm thinking of doing this, is having the pate sends rout to a patchbay that is normalized to the inputs on the lynx. Then if you're running outboard gear you can patch directly into pt and bypass the board on your outboard gear.
just my thoughts on the thing after having it installed for a grand total of 3 days. On the plus side.. does sound nice to be summing through a board again.
I am in the same boar actually. I just installed a Ghost at my studio on Sunday this week and am still unsure on what levels to run at. So anyone with advice feel free to chime in. Still working on what I want to do for workflow.
So far, when I was calibrating my oputputs from pro tools into the board via the tape returns I was setting it with the outputs set on my aurora to -10 normal. Then when I was running a two buss into a compressor I noticed I was cranking the input on that thing up quite a bit more than when I was on my previous setup.
So after setting my returns I switched the outputs back to +4 and it seems to work a little better. well, I get more in two buss going out, and the headroom seems to be able to handle it without collapsing. At least with my minimum experience so far.
With the inputs on PT I have them set to -10.
For my line in's I just set my trim levels for my outboard gear and leave 'em.
One option too. And I'm thinking of doing this, is having the pate sends rout to a patchbay that is normalized to the inputs on the lynx. Then if you're running outboard gear you can patch directly into pt and bypass the board on your outboard gear.
just my thoughts on the thing after having it installed for a grand total of 3 days. On the plus side.. does sound nice to be summing through a board again.
Snoring Hound Studio
Kalisepll, MT
Kalisepll, MT
- Wagz
- takin' a dinner break
- Posts: 186
- Joined: Mon Sep 08, 2008 4:44 am
- Location: Kalispell, MT
- Contact:
Oh, here is a question. Is there any way to send signal to your tape sends pre fader?
Snoring Hound Studio
Kalisepll, MT
Kalisepll, MT
Re: Soundcraft Ghost interfacing with recorders
Hello..It's been a while since I recorded analog.. ,but I do remember a situation similar to this..ZI used the Tascam LA-80 line converter to help remedy this..You probably could use something as the Ebtech Line Level Shifter ( 8 channel) also..Good luck..Matt C. wrote:Recently bought a Soundcraft Ghost, and today as I started the task of getting it setup, I realized that the direct outputs on the channels have a nominal level of -2dBu (unbalanced). Seems ridiculous, I guess I should have done my homework more thoroughly before buying this thing.
I know this is a popular board so I'm curious what others have done as far as interfacing this thing with recorders that are designed for either +4 or -10. I use both a Lynx Aurora and a Tascam MS16 tape machine. Both can be set for either +4 or -10, but this -2dBu thing has me baffled. If I was only recording digitally I could see it not being a real issue, but getting proper level onto tape is a bit more critical.
I'd like to just run everything at +4 so that I'm not dealing with level mismatches while using some console pres and some outboard pres during the same session. But apparently that's not in the cards for me. If anyone has some advice about optimal setup for this board, I'd appreciate it. Thanks!
- rhythm ranch
- mixes from purgatory
- Posts: 2793
- Joined: Wed May 07, 2003 8:45 pm
- Location: Corrales, NM
-
- moves faders with mind
- Posts: 2746
- Joined: Thu Jul 03, 2003 11:26 pm
- Location: Denver, CO
- Contact:
Really, twas ever thus.
-2 dBu is 6 dBu less than +4 dBu.
6 dB means half the voltage. If a balanced output drives +4 dBu, then one leg of that signal will be -2 dBu.
Since most midgrade consoles (Soundcraft, Soundtracs, the lesser Ameks, etc, etc) have unbalanced inserts and direct outs, they'll be -2. The Toft board may be an exception.
In practice, it never made a huge dent in my workflow. I ran the board set for +4, then just turned the preamp or fader up until the recorder showed reasonable levels.
-2 dBu is 6 dBu less than +4 dBu.
6 dB means half the voltage. If a balanced output drives +4 dBu, then one leg of that signal will be -2 dBu.
Since most midgrade consoles (Soundcraft, Soundtracs, the lesser Ameks, etc, etc) have unbalanced inserts and direct outs, they'll be -2. The Toft board may be an exception.
In practice, it never made a huge dent in my workflow. I ran the board set for +4, then just turned the preamp or fader up until the recorder showed reasonable levels.
"What fer?"
"Cat fur, to make kitten britches."
"Cat fur, to make kitten britches."
Yep that. All of that. The noise floor should also be attenuated about the same, and since you're running to tape, the board will not be the bottleneck for dynamic range.The Scum wrote:Really, twas ever thus.
-2 dBu is 6 dBu less than +4 dBu.
6 dB means half the voltage. If a balanced output drives +4 dBu, then one leg of that signal will be -2 dBu.
Since most midgrade consoles (Soundcraft, Soundtracs, the lesser Ameks, etc, etc) have unbalanced inserts and direct outs, they'll be -2. The Toft board may be an exception.
In practice, it never made a huge dent in my workflow. I ran the board set for +4, then just turned the preamp or fader up until the recorder showed reasonable levels.
Hey Wagz, you bought the Ghost from me. Funny, I bought it from someone on this forum too
I have the same problem on my A&H GS3000. Well not 'problem' but it's just the way it is. The guy who designed the Ghost is the same guy who designed the GS3000, so that probably has something to do with it. It's one little niggle that bothers me about it and the OP is right: I want the levels going into and coming from the tape machine to match dammit!
I've forgotten how the Ghost works by now as far as groups, but the GS3000 has a little trick to get around the -6db loss. The Ghost has separate outputs for the 8 groups, but the GS3000 doesn't. Tape outs 1, 9, 17, and 25 send group 1, tape outs 2, 10, 18, and 26 send group 2, etc, all from a little switch in the channel path. The group outs are at the proper +4 level, so even though the groups and channels all come out the same jack, all it takes is the press of a switch to get +6 in there (as long as the group fader is at unity).
The direct/group out jacks on the GS3000 are impedance balanced, and impedance balanced outputs give only an unbalanced-type level. It's because only one output driver is being utilized (on the +/tip) and the other (-/ring) is only given the same impedance to ground. That gives me the benefit of rejection, but at 6db less since there is no inverted signal being sent on the -/ring.
The Ghost has ground compensated direct outs which is similar...
I have the same problem on my A&H GS3000. Well not 'problem' but it's just the way it is. The guy who designed the Ghost is the same guy who designed the GS3000, so that probably has something to do with it. It's one little niggle that bothers me about it and the OP is right: I want the levels going into and coming from the tape machine to match dammit!
I've forgotten how the Ghost works by now as far as groups, but the GS3000 has a little trick to get around the -6db loss. The Ghost has separate outputs for the 8 groups, but the GS3000 doesn't. Tape outs 1, 9, 17, and 25 send group 1, tape outs 2, 10, 18, and 26 send group 2, etc, all from a little switch in the channel path. The group outs are at the proper +4 level, so even though the groups and channels all come out the same jack, all it takes is the press of a switch to get +6 in there (as long as the group fader is at unity).
The direct/group out jacks on the GS3000 are impedance balanced, and impedance balanced outputs give only an unbalanced-type level. It's because only one output driver is being utilized (on the +/tip) and the other (-/ring) is only given the same impedance to ground. That gives me the benefit of rejection, but at 6db less since there is no inverted signal being sent on the -/ring.
The Ghost has ground compensated direct outs which is similar...
Last edited by HSLand on Tue Jun 09, 2015 10:32 am, edited 2 times in total.
http://www.soundonsound.com/sos/jun15/a ... 615-03.htm
This was just put up. It's about the Ghost in particular. It explains a lot.
This was just put up. It's about the Ghost in particular. It explains a lot.
Who is online
Users browsing this forum: No registered users and 96 guests