Phase question
Re: Phase question
Where can I buy a hammond box?
Re: Phase question
and how do you mount XLR inputs and other things on/in (using a drill, saw etc) ?
Re: Phase question
sorry, one more thing. What are jumpers, what type should I get and what type of wire do I use when soldering the components together.
-
- gimme a little kick & snare
- Posts: 86
- Joined: Wed May 07, 2003 5:56 am
- Location: cape cod MA
Re: Phase question
I like to wire up phase reverse or pads in those Switchcraft adapters they make. You buy them unwired. XLR male to female about the size of their turnarounds.
Re: Phase question
Would someone be kind enough to tell me what are jumpers, what type should I get, and from where? Also to wire up a phase reverse box do I just use balanced mic/line cable or do I need something else?
- soundguy
- ghost haunting audio students
- Posts: 3182
- Joined: Wed May 07, 2003 12:50 pm
- Location: NYC
- Contact:
Re: Phase question
you can use standard mic cable to wire the box up. Jumping just means connect, so you just take a bit of wire and connect the appropriate terminals on the switch. you can use a trimmed piece of whatever cable you use to connect the panel connectors to the switch.
dave
dave
- thunderboy
- buyin' a studio
- Posts: 993
- Joined: Wed May 07, 2003 11:53 am
- Location: ROC, NY, USA
Re: Phase question
a jumper, in this case, would be 20-22 gauge copper wire. I like solid wire, but stranded wire is a bit easier to work with IMO. Radio Shack or any hardware store.
you don't need any cable to make this box, just the parts soundguy described.
good luck!
jt
you don't need any cable to make this box, just the parts soundguy described.
good luck!
jt
"most toreadors worth a damn are circumcized."
- Discs of Tron
- Discs of Tron
Re: Phase question
Two questions: I just wanted to clarify, I can use the copper wire to hook up the entire box right? And what do you guys use to cut the wholes in a hammond box to accomadate the XLR panel mounts?
- thunderboy
- buyin' a studio
- Posts: 993
- Joined: Wed May 07, 2003 11:53 am
- Location: ROC, NY, USA
Re: Phase question
1 -Yes.
2 - If you think you might do a lot of this type of thing, there are tools you will need. If not, just take it to a local machinist (or even someone with a decent woodshop) and have them do it for you. Bring along an XLR panel mount to ensure it gets done right!
jt
2 - If you think you might do a lot of this type of thing, there are tools you will need. If not, just take it to a local machinist (or even someone with a decent woodshop) and have them do it for you. Bring along an XLR panel mount to ensure it gets done right!
jt
"most toreadors worth a damn are circumcized."
- Discs of Tron
- Discs of Tron
Re: Phase question
thunderboy, thanks for the help, one thing though, when I asked what do you guys use to cut the holes, I know there are special tools. I wanted to know which ones (such as drills or drill presses, routers bandsaws etc...)
- thunderboy
- buyin' a studio
- Posts: 993
- Joined: Wed May 07, 2003 11:53 am
- Location: ROC, NY, USA
Re: Phase question
Well, sure. You could use a drill press. You'll need to construct a jig to hold the box in place while you drill. Use a metal cutting bit at a low speed.
Also, somewhere out there somebody sells a die cutter for this purpose. You still have to drill a small pilot hole, but you could use a power drill (careful!) for that. Sorry, but I don't know off-hand who carries this item, but I'll post it if I think of it.
jt
Also, somewhere out there somebody sells a die cutter for this purpose. You still have to drill a small pilot hole, but you could use a power drill (careful!) for that. Sorry, but I don't know off-hand who carries this item, but I'll post it if I think of it.
jt
"most toreadors worth a damn are circumcized."
- Discs of Tron
- Discs of Tron
- soundguy
- ghost haunting audio students
- Posts: 3182
- Joined: Wed May 07, 2003 12:50 pm
- Location: NYC
- Contact:
Re: Phase question
I have drilled ever hammond box I have built up with a hand drill. Ive also cursed every time I did it, but thats another story. You can get a metal bit from home depot and they sell big bits to cut the right hole, or they sell these tapered bits so you can make any size hole you want.
read this carefully:
hammond boxes are aluminum. This means they are really easy to drill. It also means that your bit, when it punches through the metal, will get caught on the box and pull the box out of your hand causing you to scream obscenities and often bleed. If you dont have a vice to hold the box, DO NOT hold it with your hand when you drill it. Hold the box firmly against the ground with your foot and drill it that way, youll be glad you did.
dave
read this carefully:
hammond boxes are aluminum. This means they are really easy to drill. It also means that your bit, when it punches through the metal, will get caught on the box and pull the box out of your hand causing you to scream obscenities and often bleed. If you dont have a vice to hold the box, DO NOT hold it with your hand when you drill it. Hold the box firmly against the ground with your foot and drill it that way, youll be glad you did.
dave
Re: Phase question
A Unibit (conical 'stepped' drill bit, about $30 at the home center) works GREAT on Hammond boxes. Since I'm such an idiot, I'm surprised how neatly my DI box came out.
And those Hammonds are very nice enclosures (thanks Dave!).
And those Hammonds are very nice enclosures (thanks Dave!).
Who is online
Users browsing this forum: No registered users and 84 guests