Studiomaster Series II 40/8/2
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
Studiomaster Series II 40/8/2
I have maybe a weird question but I was wondering if anyone had any experience with these consoles in the past. Its form the 80's and supposidly phil collins was a big promoter for these consoles. Here is the question, I friend of mine has one that he used in the eighties as his console, and for the past 15 years of so has kept it not working, he says about 8 channels are not working and the master bus. My question is, is it worth tryting to maybe salvage those eight pre-amps from him and use them for my daw? I have never really built any pre-amps, but have done alot of soldering and know my was around schematics a little. Does anyone think this is possible? Any help would be recommended.
Thanks
Thanks
-
- audio school
- Posts: 5
- Joined: Sat Jan 29, 2005 12:51 pm
- Location: New Zealand
- Contact:
I have one of these mixers, in the 16/8/2 version. I'm not sure the preamps are anything overly special. The biggest problem I've had with this desk are the inserts jack contacts oxidising, making the normalled connection dubious. If a channel doesn't go I would check those first. I also put some upgraded opamps in strategic places (the mix buss).
The mixer is retired now, in fact the power supply has stopped working and I need to sort that before i could consider selling it.
I do have all schematics except for some reason the mic pres. The circuit is fairly typical british 1980's, op amps and standard circuitry.
Larry
The mixer is retired now, in fact the power supply has stopped working and I need to sort that before i could consider selling it.
I do have all schematics except for some reason the mic pres. The circuit is fairly typical british 1980's, op amps and standard circuitry.
Larry
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
-
- audio school
- Posts: 5
- Joined: Sat Jan 29, 2005 12:51 pm
- Location: New Zealand
- Contact:
Well it is possible, were you going to mix all channels? or just take a direct out from each.
The direct out option is simplist, otherwise you need to have a mix buss. In the Series2 all the channel mix buss connections are on a common ribbon cable, quite a bit of work sorting that lot out if you don't use the existing system.
Personally I would just buy one of the many small modern mixers that are so available now.
Larry
The direct out option is simplist, otherwise you need to have a mix buss. In the Series2 all the channel mix buss connections are on a common ribbon cable, quite a bit of work sorting that lot out if you don't use the existing system.
Personally I would just buy one of the many small modern mixers that are so available now.
Larry
- mfdu
- gimme a little kick & snare
- Posts: 79
- Joined: Wed Nov 02, 2005 4:08 pm
- Location: melbourne, australia
- Contact:
i have a studiomaster series 5 16/8/2, i use it as an 8bus rather than tapping off from each channels direct out.
yes i have had to replace the insert jacks and the main out xlr's (oxidised), and i have done the internal jumper mod from -10 to +4.
i love this console. it has its own sound - can get a bit crunchy if pushed too far, but if you respect it you'll get a "much better" (read : different) sound to the current crop of micro-mixes with "invisable mic pre's".
they're not great if they're all you have. but add them in to the mix with a few different flavour pre's and they really start to show they're colours.
the eq is broad and warm with swept mid. and it is a decent size to move around on.
certainly i intend to replace it. but not to update with any "modern" DAW front-end or compact mixer. that isn't the sound i am going for. next step for me woud be an older console - something equally interesting.
what sound are you going for? if you want the crystaline "modern" sound, then go for it. ditch the studiomaster. just dont tell me. and don't complain once you've done it.
if you are after some character and a pile of handy pre's and eq's then to add to your palette . . . well, you can see where i'm going with this.
cheerio
chris.
yes i have had to replace the insert jacks and the main out xlr's (oxidised), and i have done the internal jumper mod from -10 to +4.
i love this console. it has its own sound - can get a bit crunchy if pushed too far, but if you respect it you'll get a "much better" (read : different) sound to the current crop of micro-mixes with "invisable mic pre's".
they're not great if they're all you have. but add them in to the mix with a few different flavour pre's and they really start to show they're colours.
the eq is broad and warm with swept mid. and it is a decent size to move around on.
certainly i intend to replace it. but not to update with any "modern" DAW front-end or compact mixer. that isn't the sound i am going for. next step for me woud be an older console - something equally interesting.
what sound are you going for? if you want the crystaline "modern" sound, then go for it. ditch the studiomaster. just dont tell me. and don't complain once you've done it.
if you are after some character and a pile of handy pre's and eq's then to add to your palette . . . well, you can see where i'm going with this.
cheerio
chris.
M.F.D.U.
Will record for whiskey.
Will record for whiskey.
fix it man
If you want to fix it, then start with the PSU, and work your way through the console. It takes a lot of time, patience, and a bit of money, but the good news is that you don't have to spend the money all at once, and you will get the satisfaction of fixing something.
I almost sold my console for scrap, but then realized that fixing it is not that hard. If it's modular, even better. I've heard that ribbon summers are a little noisy, you may consider a different method of summing.
greg
I almost sold my console for scrap, but then realized that fixing it is not that hard. If it's modular, even better. I've heard that ribbon summers are a little noisy, you may consider a different method of summing.
greg
going one way down a wrong way street
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
-
- audio school
- Posts: 5
- Joined: Sat Jan 29, 2005 12:51 pm
- Location: New Zealand
- Contact:
If you have an intact Series 2 mixer then obviously use it.
But to modify it in my opinion is not worth the trouble, it's just a fairly typical opamp audio circuit of the day, very adequate but it aint a Neve.
The series 5 I don't know about.
For warmth in my DAW I pass everything through a TL Audio valve compressor and that works for me, each to their own.
Larry
But to modify it in my opinion is not worth the trouble, it's just a fairly typical opamp audio circuit of the day, very adequate but it aint a Neve.
The series 5 I don't know about.
For warmth in my DAW I pass everything through a TL Audio valve compressor and that works for me, each to their own.
Larry
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
- mfdu
- gimme a little kick & snare
- Posts: 79
- Joined: Wed Nov 02, 2005 4:08 pm
- Location: melbourne, australia
- Contact:
sure it'll take up less space. because it aint a console any more.
one of these days all you'se cats are going to be saying "why did i think i could get away without a console"
sure we do our automation in the DAW. have you read any of the guff on summing boxes? multiple outs from the DAW? use the console.
what about tracking a band? reach out and grab a handfull of faders. oops - don't have a console.
EQ and mix on bounce-down? where'd that console go?
tracking via direct-outs as well as making an immediate stereo mix from the 2bus so the talent can take it with them? oh thats right - you don't have a console.
oh ok. i'll shut up now. but you'll remember this in years time and say "gee. chris may have been right"
chris.
one of these days all you'se cats are going to be saying "why did i think i could get away without a console"
sure we do our automation in the DAW. have you read any of the guff on summing boxes? multiple outs from the DAW? use the console.
what about tracking a band? reach out and grab a handfull of faders. oops - don't have a console.
EQ and mix on bounce-down? where'd that console go?
tracking via direct-outs as well as making an immediate stereo mix from the 2bus so the talent can take it with them? oh thats right - you don't have a console.
oh ok. i'll shut up now. but you'll remember this in years time and say "gee. chris may have been right"
chris.
M.F.D.U.
Will record for whiskey.
Will record for whiskey.
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
No, don't stop, Your ideas a totally being considered, THe thing is is that is not mine to begin with, its a collegues of mine and he is not using it and I was thinking of taking his broken 8 channel strips and converting them into rack useable pre-amps to go directly into my DAW, I have used a console on some occasions but am not rich enough and lucky to own one or even be able to use one on a yearly basis, I just though of instead having it sit around his studio I could take some of the channel strips and so some fixing on them and later use them while tracking with my DAW, Do wnat to go on anymore just wanted to give you the details on the siutation and see if it is a good idea or bad idea to do such a project.
- mfdu
- gimme a little kick & snare
- Posts: 79
- Joined: Wed Nov 02, 2005 4:08 pm
- Location: melbourne, australia
- Contact:
fully understand, please forgive and in the light of things you have my blessing.
the pre's certainly do more for me than a mackie or b*#&^%(
especially if you can rack them with eq and insert points intact. that way you'll get the chance of loading a compressor in on the signal path before it hits A/D.
with that flexibility, you can make the most of what you need at the time.
the main thing should be providing the right voltages.
beyond that it shouldn't be too hard to find an input point and a (pre fader - you wouldn't rack it with faders would you?) and an output point to pop your XLR or 1/4" sockets onto . . .
have you found a circuit diagram?
chris.
the pre's certainly do more for me than a mackie or b*#&^%(
especially if you can rack them with eq and insert points intact. that way you'll get the chance of loading a compressor in on the signal path before it hits A/D.
with that flexibility, you can make the most of what you need at the time.
the main thing should be providing the right voltages.
beyond that it shouldn't be too hard to find an input point and a (pre fader - you wouldn't rack it with faders would you?) and an output point to pop your XLR or 1/4" sockets onto . . .
have you found a circuit diagram?
chris.
M.F.D.U.
Will record for whiskey.
Will record for whiskey.
-
- suffering 'studio suck'
- Posts: 411
- Joined: Thu Oct 28, 2004 4:34 pm
Who is online
Users browsing this forum: No registered users and 167 guests