Tape Machine Issue
-
- suffering 'studio suck'
- Posts: 485
- Joined: Thu Sep 25, 2003 9:58 am
- Location: Vista
- Contact:
Tape Machine Issue
I'm a new owner and complete noob with a 1/4-in 2-tr machine (Otari MTR-10). I've gone through an initial alignment and calibration best I could. Things sound fine and I'm not planning on sending anything out of the studio on tape--just dumping a digital mix into it and taking it right back in at this point.
The one issue I was having tonight was a loss of level/volume coming back off the tape intermittently. At first I thought maybe it was the tape as I'd used the same one a couple of times through; but even with a new reel I had a noticeable drop in level in one part of the song I was bouncing down; for like 2 - 3 seconds; and then it came back up. Any ideas on what could be causing this? The only part of the calibration that got kind of sketchy was in the biasing; I can find the specifics in the manual if it would help--but it had to do with feeding in a square wave at 10 kHz and getting one back out at multiple speeds. It looked ok at 7.5 ips; but 15 ips was way out and 30 ips, while better, didn't look at all square. I aligned the heads using an MRL tape (I'm running GP9 tape) and they looked fine there.
Any input would be appreciated.
The one issue I was having tonight was a loss of level/volume coming back off the tape intermittently. At first I thought maybe it was the tape as I'd used the same one a couple of times through; but even with a new reel I had a noticeable drop in level in one part of the song I was bouncing down; for like 2 - 3 seconds; and then it came back up. Any ideas on what could be causing this? The only part of the calibration that got kind of sketchy was in the biasing; I can find the specifics in the manual if it would help--but it had to do with feeding in a square wave at 10 kHz and getting one back out at multiple speeds. It looked ok at 7.5 ips; but 15 ips was way out and 30 ips, while better, didn't look at all square. I aligned the heads using an MRL tape (I'm running GP9 tape) and they looked fine there.
Any input would be appreciated.
GP9 issues
Check here to read about other tapeoppers' problems with GP9
http://messageboard.tapeop.com/viewtopic.php?t=31028
....and here with 456
http://messageboard.tapeop.com/viewtopic.php?t=33323
http://messageboard.tapeop.com/viewtopic.php?t=31028
....and here with 456
http://messageboard.tapeop.com/viewtopic.php?t=33323
I've never tried GP9 on my MTR-12, but I've had problems with every reel of 499 I've tried. I just gave up and switched to 456, and havn't had any problems since.
The width of the tape w/ 499 was the problem with my tapedeck. It was actually wider than my guides, which would cause crazy shedding and dropouts like you're describing.
The width of the tape w/ 499 was the problem with my tapedeck. It was actually wider than my guides, which would cause crazy shedding and dropouts like you're describing.
- the velour fog
- buyin' a studio
- Posts: 874
- Joined: Wed May 07, 2003 9:38 am
Same here, but with 1/2". I never tried GP9 on my own machine, but had bad shedding issues with another band's Otari. On my TSR I have had issues with strange volume fluxuations using 499 -- especially when flipping to record backwards. Strangely, with 456, I've never had any issues. You are certainly demagging and cleaning enough -- I only demag after about 10-15 hours of real record time, but I clean after each session.honkyjonk wrote:... I just gave up and switched to 456, and havn't had any problems since...
When you check the square wave at 15 ips, what are you seeing?
You may also be suffering from an intermittent tension problem. When the tape tension drops, the tape to head contact is comprimised and will cause varying levels. This could also be caused by bad slitting on the tape which will affect the tape to head contact as well. If you're shedding excessively, your tape path may need adjusting. Just some thoughts.
CA
CA
Who is online
Users browsing this forum: No registered users and 56 guests