level drop when using ada8000??
-
- gimme a little kick & snare
- Posts: 86
- Joined: Mon Jan 07, 2008 8:13 pm
level drop when using ada8000??
just picked up an ada8000, got it hooked up, but when plugging my great river and sytek preamps into this thing going XLR>TRS with the ada preamps at 0, there is a huge level drop compared to just plugging them into my 002r. my GR and syteks are peaking before the level is even remotely hot going through the ada into the 002.. am I doing something really stupid? or is this common knowledge? or is my ada8000 defective? do I have to use the ADA's preamps to boost the signal--I thought everyone was avoiding them and I would like to as well. I am confused...
- Nick Sevilla
- on a wing and a prayer
- Posts: 5595
- Joined: Mon Mar 03, 2008 1:34 pm
- Location: Lake Arrowhead California USA
- Contact:
Re: level drop when using ada8000??
Hi,watergunfight wrote:just picked up an ada8000, got it hooked up, but when plugging my great river and sytek preamps into this thing going XLR>TRS with the ada preamps at 0, there is a huge level drop compared to just plugging them into my 002r. my GR and syteks are peaking before the level is even remotely hot going through the ada into the 002.. am I doing something really stupid? or is this common knowledge? or is my ada8000 defective? do I have to use the ADA's preamps to boost the signal--I thought everyone was avoiding them and I would like to as well. I am confused...
First, the ADA8000 has CALIBRATABLE inputs and outputs. Have you calibrated it yet? You'll need a good quality small flat screwdriver for this task. And the manual, which will tell you the details on how to go about this. Use a 1kHz sine tone.
Cheers
- fossiltooth
- carpal tunnel
- Posts: 1734
- Joined: Sat Mar 24, 2007 3:03 pm
- Location: Brooklyn, NY
- Contact:
Re: level drop when using ada8000??
Nah.watergunfight wrote:am I doing something really stupid?
...Unless you were unwittingly using the line amps (or mic pres) on channels 1-4 of the 002 to boost the signal.
...Or if you had the 002 inputs set to -11 instead of +4
Otherwise no.
...Unless you were doing all this in the bathtub.
Otherwise, you're doing fine!
Also...could be headroom issues. The Great River ( probably the Sytek also) has hot outputs as compared to the input headroom of the Behringer. I often had these issues with the LT going into its inserts rated at "0". I was using OSA and Biz pres into the LT which also has hot outputs..You probably can compensate for it with the GR with it's output control, as with the Sytek, it doesn't have one. Good luck
-
- gimme a little kick & snare
- Posts: 86
- Joined: Mon Jan 07, 2008 8:13 pm
Re: level drop when using ada8000??
I have not, I searched for that section of the manual and couldn't find it, also searched for "calibrate" and "calibratable" in the PDF file just to make sure I wasn't missing it...noeqplease wrote: First, the ADA8000 has CALIBRATABLE inputs and outputs. Have you calibrated it yet? You'll need a good quality small flat screwdriver for this task. And the manual, which will tell you the details on how to go about this. Use a 1kHz sine tone.
Cheers
When I'd use the sytek/gr with the 002 I'd be going into channels 5-8 with +4, without a bathtub in sight.
As for the headroom issues, I am saying that with the great river (both outputs) as hot as they can go without clipping going into the ADA still doesn't get that hot of a signal. And the sytek peaks too soon also.
Any other suggestions? Does everyone using an ADA8000 with external pres (or Digimas FS or any AD converter with built in preamps that are set at 0) have the same issue?
Re: level drop when using ada8000??
If you are running the Great River full throttle into the Berry and not getting good recording levels ( weak signal)..I would think there may be some issues with the Behringer....What about cables?watergunfight wrote:I have not, I searched for that section of the manual and couldn't find it, also searched for "calibrate" and "calibratable" in the PDF file just to make sure I wasn't missing it...noeqplease wrote: First, the ADA8000 has CALIBRATABLE inputs and outputs. Have you calibrated it yet? You'll need a good quality small flat screwdriver for this task. And the manual, which will tell you the details on how to go about this. Use a 1kHz sine tone.
Cheers
When I'd use the sytek/gr with the 002 I'd be going into channels 5-8 with +4, without a bathtub in sight.
As for the headroom issues, I am saying that with the great river (both outputs) as hot as they can go without clipping going into the ADA still doesn't get that hot of a signal. And the sytek peaks too soon also.
Any other suggestions? Does everyone using an ADA8000 with external pres (or Digimas FS or any AD converter with built in preamps that are set at 0) have the same issue?
- I'm Painting Again
- zen recordist
- Posts: 7086
- Joined: Wed May 07, 2003 2:15 am
- Location: New York, New York
- Contact:
FYI the sytek's light actually comes on 8db before it's actual clipping point..you'll find that in its manual and on their website..
the Behringer ADA8000 thing looks like it has a gain adjust..that is probaly the issue here..
you want to adjust it so that a 1.228volt sine wave at input = the average level you want to track at..ideally you should set that to accommodate the dynamic range of your program material..a lot of people use -12dbfs or -20dbfs as there reference level for typical types of program material..
the Behringer ADA8000 thing looks like it has a gain adjust..that is probaly the issue here..
you want to adjust it so that a 1.228volt sine wave at input = the average level you want to track at..ideally you should set that to accommodate the dynamic range of your program material..a lot of people use -12dbfs or -20dbfs as there reference level for typical types of program material..
-
- gimme a little kick & snare
- Posts: 86
- Joined: Mon Jan 07, 2008 8:13 pm
- fossiltooth
- carpal tunnel
- Posts: 1734
- Joined: Sat Mar 24, 2007 3:03 pm
- Location: Brooklyn, NY
- Contact:
Re: level drop when using ada8000??
[deleted]
Last edited by fossiltooth on Wed Feb 16, 2011 8:20 pm, edited 1 time in total.
-
- gimme a little kick & snare
- Posts: 86
- Joined: Mon Jan 07, 2008 8:13 pm
haha! well it was either the new aphex 142, the alesis AI3, or the ADA.
I could only find 1 person who's tried the new aphex unit, and so my decision was between a BLA modded AI3/ADA. the ADA worked out to be cheaper for apparently the same converters and the same analog stage upgrade, or at least according to the black lion website's AI3 description...
although when I called black lion today to see if anyone else had an issue with the ADA's volume, the guy told me (after trying to get me to mod my 002 ) that the alesis is way better, even though it says on the site they use the same converters and each mod is putting in new op amps.. but I've been getting a few different answers from them depending on who I talk to...
so now I am stuck with a deposit already made to black lion on an ADA that is either broken and not as good as the modded alesis, ORR just as good as the alesis and working just dandy provided someone could give me clues as to where the gain adjusting shenanigans is written.
I could only find 1 person who's tried the new aphex unit, and so my decision was between a BLA modded AI3/ADA. the ADA worked out to be cheaper for apparently the same converters and the same analog stage upgrade, or at least according to the black lion website's AI3 description...
although when I called black lion today to see if anyone else had an issue with the ADA's volume, the guy told me (after trying to get me to mod my 002 ) that the alesis is way better, even though it says on the site they use the same converters and each mod is putting in new op amps.. but I've been getting a few different answers from them depending on who I talk to...
so now I am stuck with a deposit already made to black lion on an ADA that is either broken and not as good as the modded alesis, ORR just as good as the alesis and working just dandy provided someone could give me clues as to where the gain adjusting shenanigans is written.
- chuckfurok
- steve albini likes it
- Posts: 319
- Joined: Fri Sep 19, 2003 3:49 pm
- Location: ABQ
- Contact:
- Nick Sevilla
- on a wing and a prayer
- Posts: 5595
- Joined: Mon Mar 03, 2008 1:34 pm
- Location: Lake Arrowhead California USA
- Contact:
Re: level drop when using ada8000??
Oh sorry... I though you were using an APOGEE AD8000.noeqplease wrote:Hi,watergunfight wrote:just picked up an ada8000, got it hooked up, but when plugging my great river and sytek preamps into this thing going XLR>TRS with the ada preamps at 0, there is a huge level drop compared to just plugging them into my 002r. my GR and syteks are peaking before the level is even remotely hot going through the ada into the 002.. am I doing something really stupid? or is this common knowledge? or is my ada8000 defective? do I have to use the ADA's preamps to boost the signal--I thought everyone was avoiding them and I would like to as well. I am confused...
First, the ADA8000 has CALIBRATABLE inputs and outputs. Have you calibrated it yet? You'll need a good quality small flat screwdriver for this task. And the manual, which will tell you the details on how to go about this. Use a 1kHz sine tone.
Cheers
Now THAT would sound good with the great preamps you are using. But, now that I realize my mistake, I realize your mistake.
Cheers
Even tho the Berry and the Alesis uses the same converter chip/op-amps, I think the difference in the two sounding different may be the design topology. That's why you can get a high-end unit and a low end unit, sharing some same chips,components, etc. and sound completely just that. Hi end vs lo-end!...
-
- gimme a little kick & snare
- Posts: 86
- Joined: Mon Jan 07, 2008 8:13 pm
I just double checked the specs on this thing and I am even more confused.. apparently the line inputs are 20db quieter than the mic inputs...first of all why? you mean to tell me that everyone using this thing with external pres hasn't noticed this or is just somehow dealing with it? ive been researching for awhile and haven't even heard that brought up. can someone who actually has an ada8000 chime in?
second of all--I just did a test with the same mic on the same exact source in the same spot with the same cables, one pass with the sytek through the 002 and another with the sytek through the ada8000 and there is a 12.9db (not 20) difference between the two. huh?
so my last question is what should i do to make up for that gain being lost? use xlr>xlr out of my external pres into the ada's mic inputs (which means i need 8 more xlr cables)? or xlr>trs into the line inputs and just record a really low signal into the computer? or do that but boost the gain with the ada's preamps'; or sulk some more because i bought a behringer off of ebay ahhh
second of all--I just did a test with the same mic on the same exact source in the same spot with the same cables, one pass with the sytek through the 002 and another with the sytek through the ada8000 and there is a 12.9db (not 20) difference between the two. huh?
so my last question is what should i do to make up for that gain being lost? use xlr>xlr out of my external pres into the ada's mic inputs (which means i need 8 more xlr cables)? or xlr>trs into the line inputs and just record a really low signal into the computer? or do that but boost the gain with the ada's preamps'; or sulk some more because i bought a behringer off of ebay ahhh
Well...XLR line out to XLR mic input will be worse than what you have now. (IMHO).... XLR to TRS to line input is probably the best way. You probably need to find that adjustment pot that people say is in the Berry.You might just be in the -10 level and not the +4 level which is what you probably need as mentioned. Good luck
Who is online
Users browsing this forum: No registered users and 172 guests