How can I turn a 2 channel Twin amp into a 1 channel Twin ?
How can I turn a 2 channel Twin amp into a 1 channel Twin ?
I love the tone of my Twin Reverb Reissue, but it's unnecessary loud for recording instrument after instrument like I do at home.
I heard one could easily turn this amp into a mono channel amp by removing a few valves and disconnecting 1 of the 2 speakers. Does anyone have more information about this?
Also I never use the reverb/vibrato channels, can I remove any valve that is unnecessary as a result ? Is it bad for the amplifier ?
I heard one could easily turn this amp into a mono channel amp by removing a few valves and disconnecting 1 of the 2 speakers. Does anyone have more information about this?
Also I never use the reverb/vibrato channels, can I remove any valve that is unnecessary as a result ? Is it bad for the amplifier ?
The Fender Twin is a fantastic performing amp but I agree completely about recording volume problems. I would say leave it alone and get a nice princeton reverb. The Silverface ones are ridiculously good tone and killer reverb for recording. They will never make it on stage or even in a normal rehearsal but very nice set-up for recording. If you insist on the mod I would give Jeff at Savage Amps a call for some advice.
- Sean Sullivan
- moves faders with mind
- Posts: 2555
- Joined: Sat Mar 31, 2007 2:24 pm
- Location: Nashville
- Contact:
I'm pretty sure if you take half the power tubes out, you will cut the power in half.
The reverb and vibrato are great, but if you don't use them I suggest a different amplifier. If you don't ever use the vibrato or reverb, get a Fender Princeton (not a Princeton Reverb). They are only about $400.
The reverb and vibrato are great, but if you don't use them I suggest a different amplifier. If you don't ever use the vibrato or reverb, get a Fender Princeton (not a Princeton Reverb). They are only about $400.
Still waiting for a Luna reunion
-
- george martin
- Posts: 1347
- Joined: Mon Nov 13, 2006 8:47 pm
- Location: home on the range
i take it it's too loud for recording because the 'sweet spot' you hear happens when you turn it up to about 6? twins run pretty clean up to and past halfway on your volume knob.
here's the skinny on the two things to do with the twin:
first - power tubes - the twin operates with two pairs of tubes - if you're looking at the back of the amplifier, and counting from left to right, tube 1 and 2 work together, and tube 3 and 4 work together.
if you want to cut the power in half, pull either tubes 1 and 3 or 2 and 4. they have to be pulled in a pair like this!
what will you get? about a 50w amp. you'll be clean up to about 4 on your input volume.
second - preamp tubes - you mentioned 'disabling' the normal channel. if you pull the preamp tube for that channel (which would be the tiny tube all the way on the right hand side), you're simply drawing less amplifier current and you'll get more headroom and also gain out of your vibrato channel. though, if you're pulling the pair of power tubes, you're going to get this headroom+gain anyways, so I suggest for your purposes to leave that preamp tube in. but, unplug it and listen! you won't harm the amp.
sell the reissue - the princeton is a great small amp - I'd also suggest a super reverb with a master volume -
here's the skinny on the two things to do with the twin:
first - power tubes - the twin operates with two pairs of tubes - if you're looking at the back of the amplifier, and counting from left to right, tube 1 and 2 work together, and tube 3 and 4 work together.
if you want to cut the power in half, pull either tubes 1 and 3 or 2 and 4. they have to be pulled in a pair like this!
what will you get? about a 50w amp. you'll be clean up to about 4 on your input volume.
second - preamp tubes - you mentioned 'disabling' the normal channel. if you pull the preamp tube for that channel (which would be the tiny tube all the way on the right hand side), you're simply drawing less amplifier current and you'll get more headroom and also gain out of your vibrato channel. though, if you're pulling the pair of power tubes, you're going to get this headroom+gain anyways, so I suggest for your purposes to leave that preamp tube in. but, unplug it and listen! you won't harm the amp.
sell the reissue - the princeton is a great small amp - I'd also suggest a super reverb with a master volume -
we are the village green
preservation society
god bless +6 tape
valves and serviceability
*chief tech and R&D shaman at shadow hills industries*
preservation society
god bless +6 tape
valves and serviceability
*chief tech and R&D shaman at shadow hills industries*
-
- gimme a little kick & snare
- Posts: 89
- Joined: Tue May 12, 2009 12:35 pm
- Location: Chicago, IL
Just a word of caution to those considering removal of 2 power tubes from a 4 tube amp: this will affect bias as well as output impedance and will cause variations in current draw as well as voltage variations all over the circuit. Twins are pretty robust so you most likely will not have any damage to your output transformer, and you may not even notice any negative effects on tone. But this "trick" can be hard on amps, especially ones that aren't overbuilt in the power stage. Just wanted to point this out.
Could be another case of internet info-mangling. I did a bunch of stuff to a blackface Showman (pretty much the same thing with no reverb) and according to my "research" (google)
-- the tube pairs are the two OUTSIDE tubes vs the two INSIDE tubes. Now I don't know if that's right or if 1+3 and 2+4 are correct, I'm just telling you what I googled up. I pulled the two outside tubes.
-- I read on them internets that this is hard on the transformer, and that putting a 16 ohm load on the amp would help rectify this. It also cuts the power of the amp down some more, so I put a 15" weber on it, 16 ohms.
-- and last, I put in a couple of THD Yellowjackets. These are adapters that let you run the amp off of EL84s instead of 6L6's, cutting the power down again and changing the tone to something a little less clean.
After all this it sounds pretty great, I'm using it at low volumes and it hasn't suffered any problems (except when I pulled it out of the truck and destroyed the fuse holder).
And with all these mods IT'S STILL LOUD AS HELL. I don't think I've needed run it over 4 or 5 on the knob since the mods.
-- the tube pairs are the two OUTSIDE tubes vs the two INSIDE tubes. Now I don't know if that's right or if 1+3 and 2+4 are correct, I'm just telling you what I googled up. I pulled the two outside tubes.
-- I read on them internets that this is hard on the transformer, and that putting a 16 ohm load on the amp would help rectify this. It also cuts the power of the amp down some more, so I put a 15" weber on it, 16 ohms.
-- and last, I put in a couple of THD Yellowjackets. These are adapters that let you run the amp off of EL84s instead of 6L6's, cutting the power down again and changing the tone to something a little less clean.
After all this it sounds pretty great, I'm using it at low volumes and it hasn't suffered any problems (except when I pulled it out of the truck and destroyed the fuse holder).
And with all these mods IT'S STILL LOUD AS HELL. I don't think I've needed run it over 4 or 5 on the knob since the mods.
- oldguitars
- steve albini likes it
- Posts: 356
- Joined: Wed Aug 08, 2007 10:17 am
- Location: Washington DC
- Contact:
-
- takin' a dinner break
- Posts: 156
- Joined: Tue Nov 30, 2004 12:37 am
- Location: Berkeley, CA
I've played gigs as a bassist with a guitarist using a 2-tube/1 speaker Silverface Twin--it's still painfully loud. Even when it breaks up it's more of a forceful grit, with none of the sag of a Champ/Princeton/Deluxe/Bassman.
In any case plugging into input 2 on either channel will reduce input gain & let you drive the power tubes a bit hotter at a given volume.
In any case plugging into input 2 on either channel will reduce input gain & let you drive the power tubes a bit hotter at a given volume.
In my case I have a small amp kicking around too. The showman project was more in the vein of what-if-I-did-this. Then this. And that. It sounds good, I like where it ended up.
Around here people are trying to sell Princetons for $1000 or more. Small amps are great, but sometimes I need a big sound, and the showman is great for that.
Around here people are trying to sell Princetons for $1000 or more. Small amps are great, but sometimes I need a big sound, and the showman is great for that.
ashcat_lt wrote:From my experience input 1 and 2 are equivalent in actual output volume.Wubbeneezer Garibaldi wrote:In any case plugging into input 2 on either channel will reduce input gain & let you drive the power tubes a bit hotter at a given volume.
Both are DEAFENINGLY loud... in a beautiful way.
Who is online
Users browsing this forum: No registered users and 74 guests