EQ in line of speaker cables?
- DrummerMan
- george martin
- Posts: 1436
- Joined: Thu Jun 05, 2008 12:18 pm
- Location: Los Angeles
- Contact:
EQ in line of speaker cables?
This is probably a stupid question but maybe there's an answer i haven't considered...
Is there a way to EQ a signal between an amp and speaker?
Here's my situation (and it has nothing to do with recording): I've got a stereo system that has 2 different "Zones" speaker outs, but you can only EQ Zone 1. The problem is, Zone 2 has some small in-ceiling speakers that don't produce much low end. So things in that room are pretty tinny by comparison (not terrible but worth trying to improve if possible). I feel like even if I could cut some specific mid/high frequencies that it would even things out a lot. There IS separate volume control over the 2 rooms.
Any thoughts on how to fix this? Ideas I may have overlooked?
PS - When we installed the Zone 2 speakers (many years ago) I already saw this as a potential issue, so I had them installed near the room corners with the angle of the speakers facing the corners to help mitigate the likely issues. I think it's better than it would have been, but it could still be better. I am not opposed to other physical solutions if they are not too ugly to look at...
Is there a way to EQ a signal between an amp and speaker?
Here's my situation (and it has nothing to do with recording): I've got a stereo system that has 2 different "Zones" speaker outs, but you can only EQ Zone 1. The problem is, Zone 2 has some small in-ceiling speakers that don't produce much low end. So things in that room are pretty tinny by comparison (not terrible but worth trying to improve if possible). I feel like even if I could cut some specific mid/high frequencies that it would even things out a lot. There IS separate volume control over the 2 rooms.
Any thoughts on how to fix this? Ideas I may have overlooked?
PS - When we installed the Zone 2 speakers (many years ago) I already saw this as a potential issue, so I had them installed near the room corners with the angle of the speakers facing the corners to help mitigate the likely issues. I think it's better than it would have been, but it could still be better. I am not opposed to other physical solutions if they are not too ugly to look at...
- Scodiddly
- genitals didn't survive the freeze
- Posts: 3972
- Joined: Wed Dec 10, 2003 6:38 am
- Location: Mundelein, IL, USA
- Contact:
Re: EQ in line of speaker cables?
Totally possible, and it's often done in passive speaker crossovers.
Bear in mind that it's cut only, no boost.
Bear in mind that it's cut only, no boost.
- DrummerMan
- george martin
- Posts: 1436
- Joined: Thu Jun 05, 2008 12:18 pm
- Location: Los Angeles
- Contact:
Re: EQ in line of speaker cables?
Is this a thing that I could buy cheaply, or would I need to make it? I'm imagining now basically like a guitar tone knob, but ideally I would have something graphic.
I see some passive EQs in the car stereo world but not sure if that would work.
I'm also a decent solderer so would be happy to build it.
- Scodiddly
- genitals didn't survive the freeze
- Posts: 3972
- Joined: Wed Dec 10, 2003 6:38 am
- Location: Mundelein, IL, USA
- Contact:
Re: EQ in line of speaker cables?
Generally you have to design it, and then make it. And not much adjustment possible.
Also the components have to be able to handle power, which means bigger heavier and more expensive.
Go over to Parts Express and look at the passive crossover stuff. They have a ton of resources for this kind of thing.
Also the components have to be able to handle power, which means bigger heavier and more expensive.
Go over to Parts Express and look at the passive crossover stuff. They have a ton of resources for this kind of thing.
Re: EQ in line of speaker cables?
I'm thinkin', me, first I'd look at changing the speakers ...
And since your zone is volume adjustable, you could bring a really low (use an inline pad mebbe) signal to another amp, mebbe with it's own EQ.
And since your zone is volume adjustable, you could bring a really low (use an inline pad mebbe) signal to another amp, mebbe with it's own EQ.
-
- moves faders with mind
- Posts: 2745
- Joined: Thu Jul 03, 2003 11:26 pm
- Location: Denver, CO
- Contact:
Re: EQ in line of speaker cables?
You're kinda describing the Vidsonix Virtual Crossover. It was intended for speaker DIY-ers as a tool to tune crossovers, eventually replacing it with actual passive components.
Review by Mr Pass:
https://audioxpress.com/files/attachment/2625
Somewhere inside the amp are line-level signals that would be more agreeable to EQ with whatever active EQ you've got handy.
Review by Mr Pass:
https://audioxpress.com/files/attachment/2625
Apparently now discontinued.We like the VCB-100 a lot, and recommend it highly.
Somewhere inside the amp are line-level signals that would be more agreeable to EQ with whatever active EQ you've got handy.
"What fer?"
"Cat fur, to make kitten britches."
"Cat fur, to make kitten britches."
-
- TapeOp Admin
- Posts: 1665
- Joined: Thu May 01, 2003 11:50 am
- Location: Portland, OR
- Contact:
Re: EQ in line of speaker cables?
"I had them installed near the room corners with the angle of the speakers facing the corners" if I'm not mistaken, this would likely introduce comb filtering/phase cancellation and would affect lower frequency energy more than high end...
Larry Crane, Editor/Founder Tape Op Magazine
please visit www.tapeop.com for contact information
(do not send private messages via this board!)
www.larry-crane.com
please visit www.tapeop.com for contact information
(do not send private messages via this board!)
www.larry-crane.com
- DrummerMan
- george martin
- Posts: 1436
- Joined: Thu Jun 05, 2008 12:18 pm
- Location: Los Angeles
- Contact:
Re: EQ in line of speaker cables?
Interesting. I was thinking of it like how some bass cabinets and other systems using small speakers will have the speakers facing the floor or some other physical barrier to artificially enhance the low end, but you could be right. Rotating the speakers' directions would be the easiest of all solutions to try probably...TapeOpLarry wrote: ↑Mon Apr 27, 2020 4:07 pm"I had them installed near the room corners with the angle of the speakers facing the corners" if I'm not mistaken, this would likely introduce comb filtering/phase cancellation and would affect lower frequency energy more than high end...
Who is online
Users browsing this forum: No registered users and 73 guests