If you are bussing them to one track, you need to get the phase right at the source. Otherwise, you are completely screwed.bradjacob wrote:I am! That's when the EQ doesn't seem to help.thecheat wrote:Unless you're bussing to one track, no. Mabye theres a tuning/placement issue.bradjacob wrote:With the below scenario, is this observation true?
Scenario
If two kick-tracks are recorded (out of phase). Only to later to be discovered by someone hired to mix said tracks. When played back, the mixer engages TRIM plug and flips the phase-switch. The tracks now sound pretty "ok"... (or better than they were)...
Observation
While tracking out of phase, the mics are canceling each other out - to some degree, thus limiting the amount of captured of low end.
So then, when you flip the switch, and try to boost the low end, it'll never really change it all that much because when it was tracked, the low end signal was reduced and very little made it to tape. So when boosting, not much happens?
Yes/No?
Is Anyone Using Two Mics For Kick Drum?
- farview
- tinnitus
- Posts: 1204
- Joined: Tue Aug 31, 2004 1:42 pm
- Location: St. Charles (chicago) IL
- Contact:
- farview
- tinnitus
- Posts: 1204
- Joined: Tue Aug 31, 2004 1:42 pm
- Location: St. Charles (chicago) IL
- Contact:
What I normally do, when I bother to use two mics for kick, is high-pass the outside mic and low pass the inside mic. The idea is to just keep what you like about each mic, then mix to taste. But, I haven't been in the position of haing to buss the mics together on the way to tape in years. I remember having to move the outside mic around a lot until I got the phase working. The hi and low pass filters make it easier because all the phase issues end up in the middle, where you tend to cut a little anyway. Moving the mics around just changes the frequency of the cancelation.
- @?,*???&?
- on a wing and a prayer
- Posts: 5804
- Joined: Wed May 07, 2003 4:36 pm
- Location: Just left on the FM dial
- Contact:
You should start making records and stop working by day in an office.T-rex wrote:No. Please don't listen to Jeff.bradjacob wrote:Actually, looking at the chart, at 40Hz, there is only a 2db drop off. Not a real show-stopper. And freqs of 20 & 30 - are they that important to be hyped?@?,*???&? wrote:20Hz, 30Hz, 60Hz, all great frequencies to present that kind of low-end you can stand on.
I will if you will!@?,*???&? wrote:You should start making records and stop working by day in an office.T-rex wrote:No. Please don't listen to Jeff.bradjacob wrote:Actually, looking at the chart, at 40Hz, there is only a 2db drop off. Not a real show-stopper. And freqs of 20 & 30 - are they that important to be hyped?@?,*???&? wrote:20Hz, 30Hz, 60Hz, all great frequencies to present that kind of low-end you can stand on.
[Asked whether his shades are prescription or just to look cool]
Guy: Well, I am the drummer.
Guy: Well, I am the drummer.
farview wrote:Perhaps http://www.tritonedigital.com/product_i ... ucts_id=33bradjacob wrote:If you are bussing them to one track, you need to get the phase right at the source. Otherwise, you are completely screwed.thecheat wrote:I am! That's when the EQ doesn't seem to help.bradjacob wrote:With the below scenario, is this observation true?
Scenario
If two kick-tracks ......
...Unless you're bussing to one track, no. Mabye theres a tuning/placement issue.
could help if you are ITB?
"There is nothing in a caterpillar that tells you it's going to be a butterfly."
R. Buckminster Fuller
R. Buckminster Fuller
I hate to admit it but I kind of agree with jeff
more dynamics have rolloffs in the bass than condensors
and the subkick "mic" isn't as much a mic as it is a dynamic speaker, being used as a mic.
421s, re20s, SM7bs, 441s, even the d112 has the rolloff. it would probably be sooner but since the low end boost is in place it moves the rolloff back, but it is present. stuff like the 4047 doesn't roll off even to the bitter end(20 hz and beyond). the average condensors have less likelihood of rolling off than the average dynamic.
that being said I have never thought something like the e602 lacked bottom end, and even if the mic I was using for kick did lack bottom end below 40 hz, I have to question if that rolloff might or might not be the best thing for the mix. Do I want a plump 20 hz on a close mic'd kick? Do I hear a plump 20 hz when I stand 9' away from the drums in the room as the drummer plays?
Aesthetics.
I find something like an e602 and a room mic of some sort works great. If I do use 2 mics specifically for the kick, which I rarely do cause the close mic + room mics picks up all the kick character I could ever want, I prefer something like a 4047 + e602. 2 mics works better for me than a subkick everytime IMO. But I really see little need in using 2 mics on the kick, because both mics are picking up the same general sound of, mic inside or near kick. I'd much rather have a mic away, and a mic close, than two mics next to each other or in near proximity to the kick. and incase the real speakers break it helps to have both NS10s in the control room.
more dynamics have rolloffs in the bass than condensors
and the subkick "mic" isn't as much a mic as it is a dynamic speaker, being used as a mic.
421s, re20s, SM7bs, 441s, even the d112 has the rolloff. it would probably be sooner but since the low end boost is in place it moves the rolloff back, but it is present. stuff like the 4047 doesn't roll off even to the bitter end(20 hz and beyond). the average condensors have less likelihood of rolling off than the average dynamic.
that being said I have never thought something like the e602 lacked bottom end, and even if the mic I was using for kick did lack bottom end below 40 hz, I have to question if that rolloff might or might not be the best thing for the mix. Do I want a plump 20 hz on a close mic'd kick? Do I hear a plump 20 hz when I stand 9' away from the drums in the room as the drummer plays?
Aesthetics.
I find something like an e602 and a room mic of some sort works great. If I do use 2 mics specifically for the kick, which I rarely do cause the close mic + room mics picks up all the kick character I could ever want, I prefer something like a 4047 + e602. 2 mics works better for me than a subkick everytime IMO. But I really see little need in using 2 mics on the kick, because both mics are picking up the same general sound of, mic inside or near kick. I'd much rather have a mic away, and a mic close, than two mics next to each other or in near proximity to the kick. and incase the real speakers break it helps to have both NS10s in the control room.
Real friends stab you in the front.
Oscar Wilde
Failed audio engineer & pro studio tech turned Component level motherboard repair store in New York
Oscar Wilde
Failed audio engineer & pro studio tech turned Component level motherboard repair store in New York
This is what I am saying. I personally love my Mouse on outside of kick duties. But saying that you are shooting yourself in the foot by recording a BD with a D12 seems a little crazy. Unless this is rap or dance music, the BD is going to be predominantly playing above 50 hz and probably between 63 and 80 hz or even higher. The roll off on dynamics is generally taking care of the sub bass crap that 99% of systems can't reproduce and the high end systems generally hav 25 or 30 hz subsonic filters to filter out. Of course its there, unless you filter it. But how much 25 hz do you regularly use on BD in a mix?rwc wrote:
that being said I have never thought something like the e602 lacked bottom end, and even if the mic I was using for kick did lack bottom end below 40 hz, I have to question if that rolloff might or might not be the best thing for the mix. Do I want a plump 20 hz on a close mic'd kick? Do I hear a plump 20 hz when I stand 9' away from the drums in the room as the drummer plays?
[Asked whether his shades are prescription or just to look cool]
Guy: Well, I am the drummer.
Guy: Well, I am the drummer.
-
- speech impediment
- Posts: 4270
- Joined: Tue Aug 12, 2003 5:31 pm
- Location: Norman, OK
- Contact:
with a pair of 414's about 6' in front of the bass drum and about 1.5' off the ground, I get such a great representation of the whole kit (bass drum included) that I could legitimately get away with no mic on the kick drum. I'd say I usually get a good 80% of the sound of the bass drum from these room mics.
I used an AT4050 as a room mic, low, 4.5' in front of the kit once and I forgot to have the kick drum mic plugged in and I thought it was.
I felt like a fucking moron, but it says something for that mic in that position, that I didn't even think to check the kick mic until I saw afterward, the flat waveform..
The 4050 is similar to the 414 so I am not surprised that worked for you.
I felt like a fucking moron, but it says something for that mic in that position, that I didn't even think to check the kick mic until I saw afterward, the flat waveform..
The 4050 is similar to the 414 so I am not surprised that worked for you.
Real friends stab you in the front.
Oscar Wilde
Failed audio engineer & pro studio tech turned Component level motherboard repair store in New York
Oscar Wilde
Failed audio engineer & pro studio tech turned Component level motherboard repair store in New York
-
- zen recordist
- Posts: 6687
- Joined: Wed May 07, 2003 11:15 am
-
- speech impediment
- Posts: 4270
- Joined: Tue Aug 12, 2003 5:31 pm
- Location: Norman, OK
- Contact:
-
- speech impediment
- Posts: 4270
- Joined: Tue Aug 12, 2003 5:31 pm
- Location: Norman, OK
- Contact:
Who is online
Users browsing this forum: No registered users and 41 guests